The thickness and surface of a steel plate can be seen at a glance, but the chemical composition, the mechanical values and the production batch it belongs to are told only by the material certificate. In custom fabrication, steel construction and wear plate work, this document is the first proof that a part is being made from the grade the drawing calls for. This article explains, from a fabricator's point of view, what the certificate says, how the EN 10204 document types differ and how part traceability is kept on the shop floor.

What Is a Material Certificate and Why Is It Requested?

A material certificate is issued by the steel producer for a specific batch of plate, tube or section. It records the chemical composition, the mechanical properties and the conformity of that batch to the relevant standard. It is the only reliable way to show that the material arriving at the workshop is the same as the grade written on the order. Using the wrong grade in a load-bearing steel structure, in a part working under pressure or in a wear zone can shorten service life or create a safety risk. For this reason many customer specifications explicitly require certified material and require that the certificate can be linked to the finished part.

EN 10204 Document Types: 2.1, 2.2, 3.1 and 3.2

Certificates for steel products are usually classified by the document types in the EN 10204 standard. These types define who issued the document and what kind of inspection it rests on.

2.1 and 2.2: Declaration and Test Report

Type 2.1 is a declaration of compliance in which the producer states that the product meets the order; it contains no measured result for the specific batch. Type 2.2 is a test report in which results are based on non-specific inspection rather than on the delivered product itself. These two types may be acceptable for low-risk work where only general assurance is needed.

3.1: Specific Inspection Certificate

Type 3.1 is issued by the producer through an authorized representative independent of the manufacturing department, and it contains actual inspection results for the delivered product. The chemical analysis and mechanical test results belong to that batch. In custom fabrication this is the document type requested most often.

3.2: Validated by a Third Party

For type 3.2 the document is also validated by the purchaser's authorized representative or by an independent body in addition to the producer. This level may be required for critical pressure equipment and for certain project specifications. Which document type is needed should be clear from the customer specification and the applicable project standard.

What Can Be Read From the Certificate?

Treating the certificate as paper to be filed means not using the information in it. For a fabricator the important headings are the material grade and standard, the heat (cast) number, the chemical composition, yield and tensile strength with elongation, impact test results where required and the delivery condition. The chemical composition is decisive for welding and thermal cutting decisions, because the proportion of carbon and alloying elements affects preheating need and cracking tendency. The mechanical values give an idea of bending and forming capacity. Whether the values fall within the limits allowed for the ordered grade should be checked when the material enters the shop.

Heat Number and Part Traceability

The heat number links the material to the steel melt it came from. Stamped or painted on the plate, this number must match the number on the certificate. Once the match is confirmed, a finished part can be traced back to the plate it was cut from. Traceability makes it possible to find the affected parts quickly if a customer complaint arrives or a problem is later found in a material batch. Without traceability, every job made from a questionable batch would have to be treated as suspect.

Keeping the Marking Through Cutting and Bending

The most fragile point in traceability is the moment a plate is cut into several parts. When a plate is divided by laser, plasma or oxy-fuel cutting, the area carrying the heat number may not remain on a given part. For this reason the number must be transferred to each part or each group of parts before or immediately after cutting. In practice this is done with stamping, a marking pen or a part tag, and the method must survive later painting and coating steps. Offcuts should be marked in the same way, and unidentified scrap pieces should not be used on certified jobs. Recording in the nesting plan which parts from a plate belong to which job also makes traceability easier.

How the Certificate Affects Cutting and Welding Decisions

The chemical composition on the certificate is a direct input for thermal cutting and welding of thick plate. On steels with a high carbon equivalent the risk of edge cracking after cutting can increase; we covered this in our article on preheating and cutting speed for thick plate in oxy-fuel cutting. The same information also influences which cutting method is chosen for joint preparation, which is compared in our guide to weld edge preparation with oxy-fuel and plasma cutting. The certificate is therefore not only a quality record but also a technical data source for setting process parameters.

Verifying That the Certificate Matches the Part

A document sitting in a file does not guarantee that the material is correct. At goods-in, plate thickness, dimensions and markings should be compared with the certificate. In series production this check becomes part of first article approval, and the material batch used for each series is linked to the measurement records. How first article approval and the measurement plan are set up is described in our article on quality control in series production. When the certificate, the measurement record and the part tag are kept together, the quality file becomes complete.

Record Keeping and Delivery to the Customer

Certificates should be stored linked to the work order and batch number. If the customer specification allows, a digital copy is kept; otherwise a printed copy is added to the delivery file. Retention time is set by the project specification and applicable regulations, and discarding documents too early can leave a gap in evidence if a dispute arises later. A delivery file that contains the certificate, the measurement report and, where needed, inspection records lets the job be verified from one place.

Common Mistakes

One of the most common mistakes in workshops is requesting the certificate at order stage but not checking it at goods-in. Another is failing to transfer the heat number to parts after the plate is cut. Mixing up plates of similar grade from different batches, and accepting the wrong standard because grade names look alike, are also recurring problems. Most of these errors can be largely prevented by writing goods-in inspection and marking discipline into the workshop procedure.

DMK Makina's Approach

Based in Lüleburgaz and serving customers in Thrace and Marmara as well as industrial projects across Turkey and Europe, DMK Makina receives material together with its certificate for custom and welded fabrication jobs and transfers the heat number to cut parts when required. The document type needed is clarified with the customer specification at quotation stage, so that work does not stop for a missing document after production has begun.

Conclusion

The material certificate is the starting point of a fabrication quality file. Choosing the right document type, checking it at goods-in and carrying the heat number through to the finished parts keep traceability intact. Share the material grade and document requirement of your project and we can agree the right certificate and record plan together.